Get Your Roof Quote!

Learn More

West Palm Beach Tile Roof Repair: PortoSol Eyebrow Roof Repair

This West Palm Beach tile roof repair was completed on a small concrete tile eyebrow roof at a home in the gated PortoSol community, ZIP code 33411. The homeowner noticed water coming through a kitchen light, and an interior restoration company used an infrared moisture scan to identify where moisture was present in the wall. The scan pointed to the rear eyebrow roof, where BLU Roofing found a significant area of deteriorated plywood and a separate rotted fascia section.

Quick Summary

BLU Roofing repaired a leaking concrete tile eyebrow roof in PortoSol, West Palm Beach. The approximately 12-year-old roof had a small interior leak but a much larger area of damaged plywood than expected, along with rotted cedar fascia at the right corner. The crew removed and reused the concrete tiles, replaced the damaged decking and fascia, installed a six-inch peel-and-stick perimeter strip, new white drip edge, eave enclosure, and CertainTeed SA granulated cap sheet, then reinstalled the tiles with ICP Polyset AH-160 adhesive foam and color-matched mortar. The pool and patio were fully protected during the work.

Table of Contents

Project Facts

Community PortoSol, West Palm Beach, Florida 33411
Property Single-family home in a gated community
Roof section Small rear concrete tile eyebrow roof overhang
Approximate roof age Approximately 12 years
Interior symptom Water coming through a kitchen light
Leak location Middle-to-left side of the rear eyebrow roof
Wood repairs Damaged roof decking and the entire right corner of the cedar fascia
Underlayment CertainTeed SA granulated cap sheet over a six-inch perimeter peel-and-stick membrane strip
Edge details New white drip edge and eave enclosure, also called bird stop
Tile installation Existing tiles reused and reset with ICP Polyset AH-160 adhesive foam
Timeline Full-day repair with Peter, two crew members, and one helper
Follow-up Completed almost one month before publication, with substantial rain and no callbacks reported

How the Leak Was Located

The homeowner noticed water coming through a kitchen light. An interior restoration company that has worked with BLU Roofing for years was involved first and used an infrared moisture scan to identify where moisture was present in the wall. The scan helped point the investigation toward the small rear eyebrow roof overhang.

There was no attic in this roof section, so an attic inspection was not possible. A hose test was not needed because the moisture scan identified the affected area and the roof condition could be inspected directly. The leak was on the middle-to-left side of the eyebrow roof.

BLU Roofing’s roof repair service focuses on tracing the actual water-entry area and determining what must be opened to complete the repair correctly. In this case, the visible interior symptom was small, but the roof opening showed that the underlying damage was more extensive than the kitchen leak suggested.

Opening the Eyebrow Roof

To repair the leak properly and replace the fascia, the crew removed the concrete tiles and the existing underlayment system down to the roof decking. The team worked carefully and successfully removed the tiles without breaking them, allowing the existing tile to be reused.

The roof was approximately 12 years old, so the tile covering was still suitable for reuse. The damaged area was not a reason to replace the entire main roof. Instead, the small eyebrow roof section was opened so the decking, fascia, perimeter edge, and underlayment could be inspected and rebuilt.

West Palm Beach tile roof repair

The crew was surprised by the size of the damaged plywood area compared with the relatively small amount of water that had entered the kitchen. A small interior leak does not always indicate a small roof problem. Water can travel through a roof assembly and continue affecting the decking before the interior symptom becomes obvious.

Replacing the Decking and Cedar Fascia

West Palm Beach tile roof repair in PortoSol

The deteriorated plywood was cut out and replaced with new roof decking. The new decking was nailed according to the applicable requirements for the repair. The damaged fascia was also removed from the entire right corner of the eyebrow roof and replaced with cedar.

The fascia repair was part of the reason the entire small roof section needed to be opened. Replacing the fascia while leaving the surrounding roof system closed would not have allowed the damaged edge and adjacent decking to be properly inspected. Completing both repairs together allowed the crew to rebuild the roof edge as one connected system.

West Palm Beach tile roof repair in PortoSol

Rebuilding the Roof System

Once the damaged plywood and fascia were replaced, BLU Roofing rebuilt the roof system in sequence:

  1. A six-inch-wide peel-and-stick membrane strip was installed around the roof edge as added protection beneath the drip edge.
  2. New white drip edge was installed over the perimeter membrane strip.
  3. The drip edge was primed before the next membrane layer was applied.
  4. CertainTeed SA granulated cap sheet was installed as the new tile-roof underlayment.
  5. The new underlayment was integrated with the existing roof-to-wall flashing, which was in excellent condition.
  6. The separate eave enclosure, also called bird stop, was reinstalled along the eave.
  7. The existing concrete tiles were placed back in position with ICP Polyset AH-160 two-part polyurethane adhesive foam.
  8. Color-matched mortar was installed to finish the tile details and match the existing roof.

The eave enclosure includes small weep openings that allow water beneath the tile covering to escape at the eave. Concrete tile is water-shedding rather than the primary waterproofing layer, so the underlayment and properly detailed edge components are important parts of the roof system beneath the tiles.

The roof-to-wall flashing did not need to be replaced. It was inspected and found to be in excellent condition, so the new repair was tied into the existing flashing rather than disturbing a sound component unnecessarily.

West Palm Beach tile roof repair in PortoSol

Protecting the Pool and Patio

The eyebrow roof was directly above a pool and patio area, so the crew protected the entire pool and the patio below before removing tile, decking, fascia, and underlayment. This preparation helped contain roofing debris and protect the homeowner’s property while the work was underway.

Protection is especially important when a localized tile roof repair is performed above a pool, patio, landscaping, or other finished areas. The work area was cleaned carefully after the roof and fascia repairs were completed.

Completion and Follow-Up

This was a full-day repair completed with Peter, two crew members, and one helper. The work was scheduled for a sunny day, and the weather cooperated. The completed roof section was checked, the existing tiles were successfully reused, and the property was cleaned before the crew left.

The repair was completed almost one month before this Project Spotlight was prepared. The area has received substantial rain since the work was finished, and there have been no callbacks.

PortoSol repairs of this type did not require HOA approval, and a permit was not required for this localized repair. The work addressed a specific eyebrow roof section rather than replacing the home’s entire concrete tile roof.

This West Palm Beach tile roof repair shows why a small interior leak can require a broader roof opening. Once the tiles were removed, BLU Roofing could inspect the decking and fascia, replace the damaged wood, protect the roof edge, reconnect the new underlayment to sound existing flashing, and reinstall the tile covering as part of a complete repair.

For homeowners comparing repair and replacement options, BLU Roofing’s broader roofing service information explains the types of shingle, tile, metal, and flat or low-slope roofing work provided across South Florida.

Written By: Peter Menke

Peter Menke is the owner of BLU Roofing and has been serving the South Florida roofing industry for over 6 years. He founded BLU Roofing to provide homeowners with transparent, accurate information grounded in real Florida roofing conditions and building practices. License #CCC1337285.

BLU Roofing provides roof inspections, repairs, restoration, and replacement for shingle, tile, metal, and flat or low-slope roof systems across Palm Beach, Martin, and Broward Counties.

Related Articles

Plantation silicone roof coating

Plantation Silicone Roof Coating: Secluded Gardens Pool Patio Project

This Plantation silicone roof coating project addressed a leaking pool-patio roof in Plantations Secluded Gardens, also listed in some records as Plantations Secluded Gard, in Plantation, Florida 33317. The homeowner had two roofing concerns in nearby areas: a shingle-roof water entry around a transition near a pipe boot, and a built-up modified roof over the pool deck that was leaking around its perimeter. BLU Roofing repaired both areas during the same scheduled visit and restored the flat roof with silicone coating.

Quick Summary

BLU Roofing repaired two nearby roof issues at a Plantation home in Plantations Secluded Gardens. The shingle-roof investigation found that the main water entry was at a transition near the pipe boot, along with a second nearby leak that had not yet caused an interior stain. The team repaired both areas, replaced the pipe boot, installed Polyglass TU Plus underlayment, and matched the existing shingles with GAF Timberline HDZ shingles. On the pool-patio roof, the modified roofing membrane had begun lifting around the three-inch drip edge. The crew cleaned and dried the roof, rebuilt the full perimeter with new modified roofing cement, membrane, and granules, then applied TRI-BUILT Roof X Tender 985 Super Silicone across the flat roof. The work was completed in one day, allowing the homeowner to address both repairs in one visit.

Table of Contents

Project Facts

Subdivision Plantations Secluded Gardens, also listed as Plantations Secluded Gard
Location Plantation, Broward County, Florida 33317
Property Single-family home with a pool deck and attached screen enclosure
Shingle roof Approximately 10 years old, with a tongue-and-groove roof deck
Flat roof Built-up modified roof over the rear pool deck, also approximately 10 years old
Shingle-side scope Transition repair, nearby second leak repair, pipe-boot replacement, underlayment, and shingle replacement
Shingle materials Polyglass TU Plus underlayment and GAF Timberline HDZ shingles matched to the existing roof
Flat-roof scope Perimeter rebuild, modified roofing cement, membrane, granules, and silicone coating
Coating TRI-BUILT Roof X Tender 985 Super Silicone Roof Coating
Primer and fabric No primer or polyester fabric was used on the flat roof
Timeline Completed in one day, with Peter and generally two crew members present

Two Roofing Issues at One Home

The homeowner had a water stain inside the house and two roof areas requiring attention. One issue involved the shingle roof, where the initial concern was near a pipe boot. The other involved the built-up modified roof over the rear pool deck and screen enclosure, where the perimeter was allowing water to seep into the roof edge.

The two systems were close enough that it made sense to inspect and address both during the same project. BLU Roofing’s roof repair service is based on identifying the actual water-entry area rather than assuming that the most visible roof penetration is always the source.

Investigating the Shingle Roof Leak

The shingle roof was approximately 10 years old and had a tongue-and-groove roof deck. The attic crawl space was extremely tight, but the crew was able to reach the relevant area and confirm where the water was entering.

The pipe boot was near the affected area, but the investigation showed that the primary water entry was more closely related to the transition. The crew also identified a second stain approximately two to three feet away. That second area had not yet produced an interior leak, but it was close to the first problem and accessible while the roof was open, so both areas were repaired during the same visit.

The existing pipe boot was replaced rather than reused. The shingle-side work also included Polyglass TU Plus underlayment and GAF Timberline HDZ shingles selected to provide the best available match to the existing shingle roof. The post does not identify the pipe boot as the confirmed source of all the water because the inspection found the transition and the nearby second area also required attention.

Repairing the Pool-Patio Flat Roof

The second roof system was a built-up modified roof over the rear pool deck. A screen enclosure was attached to the patio area. The modified roofing membrane was beginning to lift around the perimeter near the three-inch drip edge. That lifting created a path for water to seep into the edge of the roof and contributed to the early fascia rot that the homeowner had noticed.

The fascia damage was limited and difficult to access because the screen enclosure would have needed to be detached to replace it. The homeowner decided that replacing the small fascia section was not worthwhile under the circumstances. Instead, the roofing perimeter was opened and rebuilt to address the water-entry area and seal the edge of the roof properly.

Because the roof was directly over the pool, the pool had to be covered before the crew cleaned the roof. Dirt, loose granules, roofing debris, and other material on the modified roof could otherwise have fallen into the pool during preparation. Covering the entire pool helped protect it while the roof was cleaned, dried, repaired, and coated.

The flat-roof repair sequence was:

  1. Clean the roof and allow it to dry fully.
  2. Cut the existing perimeter membrane back beyond the drip edge, approximately four inches for this repair.
  3. Rebuild the entire perimeter with new modified roofing cement and membrane.
  4. Apply granules to the repaired perimeter area.
  5. Apply the silicone coating over the restored flat-roof surface.

The perimeter was repaired before coating. This matters because a coating is not a substitute for rebuilding a failing roof edge. The roof was cleaned and allowed to dry before the seam and perimeter work continued.

Applying the Silicone Coating

After the perimeter was rebuilt, BLU Roofing coated the flat roof with white TRI-BUILT Roof X Tender 985 Super Silicone Roof Coating. No primer was required for this project.

Unlike some aluminum-panel projects where fabric may be used to reinforce seams, this roof was a continuous modified roof surface without panel seams.

The coating was applied after the roof was cleaned, dried, and repaired. The project-specific sequence was perimeter restoration first, followed by the silicone coating across the flat roof. This is different from applying a coating directly over a damaged or actively vulnerable perimeter without correcting the edge condition.

The roof also had areas of ponding water, which are common on low-slope and flat roof systems when water does not drain completely after rain. Repeated ponding can contribute to faster degradation of a roofing system. Silicone roof coatings are commonly selected for their strong resistance to ponding-water exposure, subject to the requirements of the specific product and roof assembly. On this project, the silicone coating was intended to help protect the restored roof and extend its service life, not to replace the perimeter repairs that had to be completed first.

BLU Roofing’s residential roof coating guide explains why cleaning, drying, repairs, product selection, and system-specific application requirements should be considered before a roof is coated. This project followed that repair-first approach by rebuilding the perimeter before applying the silicone.

Why Combining the Work Helped

The homeowner could have scheduled the shingle-side repair and the pool-patio roof restoration as separate projects. Completing them separately would have meant two scheduled workdays and two trips to the property. Because both issues were identified during the same overall project, BLU Roofing was able to complete both repairs in one visit and bundle the scope into one scheduled job.

The bundled approach also allowed the crew to address the nearby second shingle-roof leak while the area was already open. That type of coordination can be useful when a homeowner has more than one roof system or more than one water-entry concern at the same property.

Plantation silicone roof coating
Plantation silicone roof coating in Plantations Secluded Gardens

Completion and Homeowner Feedback

The project was completed in one day. Peter was present, with generally two crew members working on the project and a third worker helping for part of the day while handling other errands. The homeowner was very happy with the completed work and left an excellent review.

This Plantation silicone roof coating project shows why a roof coating should be part of a complete repair plan rather than a shortcut around damaged roof edges. BLU Roofing repaired the modified roof perimeter, addressed the nearby shingle-roof water-entry areas, replaced the pipe boot, and then applied silicone coating over the restored pool-patio roof.

This type of repair did not require a permit or HOA approval, according to the project information supplied for this job. No project price is included.

BLU Roofing provides roof inspections, repairs, restoration, and replacement for shingle, tile, metal, and flat or low-slope roof systems across Palm Beach, Martin, and Broward Counties. The company works with homeowners to identify the actual roof condition and select a practical scope rather than treating every leak as an automatic full replacement.

Written By: Peter Menke

Peter Menke is the owner of BLU Roofing and has been serving the South Florida roofing industry for over 6 years. He founded BLU Roofing to provide homeowners with transparent, accurate information grounded in real Florida roofing conditions and building practices. License #CCC1337285.

BLU Roofing provides roof inspections, repairs, restoration, and replacement for shingle, tile, metal, and flat or low-slope roof systems across Palm Beach, Martin, and Broward Counties.

Read More »
Delray Beach silicone roof coating

Delray Beach Silicone Roof Coating: Colombo Court Patio Roof Restoration

This Delray Beach silicone roof coating project restored an approximately 400 to 500 square-foot aluminum-panel patio roof at a home in the Bel Air community, in the Colombo Court area of Delray Beach, Florida 33484. The enclosed patio roof was leaking through the seams where the aluminum panels came together. The aluminum panels themselves were in great condition, so the project focused on cleaning, seam treatment, and a new silicone coating rather than replacing the panel roof.

Quick Summary

BLU Roofing restored a leaking aluminum-panel patio roof in Colombo Court, Delray Beach. The roof had no existing seam tape, but the aluminum panels were in good condition. The crew cleaned the roof and gutters, blew off the water, allowed the surface to dry fully, installed new tape at the panel seams, applied white TRI-BUILT Roof X Tender 985 Super Silicone over the seams, and then applied one full field coat across the patio roof. No polyester fabric was used on this project because of the roof’s approximately 5/12 pitch, according to Peter’s project-specific explanation. The two-person crew completed the work Saturday by early afternoon.

Table of Contents

Project Facts

Community Bel Air, Colombo Court area, Delray Beach, Florida 33484
Property Single-family home with an enclosed rear patio
Patio roof Aluminum-panel roof, approximately 400 to 500 square feet
Roof pitch Approximately 5/12
Reported problem Water entering through the seams where the aluminum panels meet
Existing condition Aluminum panels in great condition, with no existing seam tape reported
Product White TRI-BUILT Roof X Tender 985 Super Silicone Roof Coating
Preparation Roof and gutter cleaning, blow-off, and full drying before coating
Seam treatment New tape at the aluminum-panel seams, followed by silicone coating over the tape
Field coating One full field coat over the aluminum-panel patio roof
Crew and timeline Peter and one crew member, completed Saturday by early afternoon

How the Homeowner Found BLU Roofing

The homeowner found BLU Roofing while using ChatGPT to look for roofing contractors and compare bids. ChatGPT recommended BLU Roofing, and the homeowner had also seen an earlier BLU Roofing project spotlight about coating an aluminum-panel roof.

The homeowner called on Wednesday evening, and BLU Roofing scheduled the inspection for Friday. During the consultation, the homeowner asked about the proposed product and the available options. Peter reviewed the roof and the planned scope with him. After the inspection, the homeowner chose BLU Roofing, signed the agreement Friday night, and the crew arrived Saturday morning.

This is one homeowner’s reported path to finding the company. It does not mean that BLU Roofing is the only company recommended by ChatGPT, and ChatGPT did not inspect the roof or independently verify the completed work.

The Aluminum-Panel Roof Condition

The rear patio roof was enclosed, with a concrete patio floor below. The roof had been leaking through the seams where the aluminum panels met. During the inspection, Peter found that the aluminum panels themselves were in great condition. The reported issue was concentrated at the panel seams, where no existing seam tape was present.

No old sealant removal was needed for this project. Other than cleaning, blowing off the water, and allowing the roof to dry completely, no additional surface-preparation step was reported. There was also no reported repair to a separate flashing, roof-to-house transition, perimeter, or fastener issue. The adjacent concrete tile main roof was visible in the project photos, but it was not part of this repair scope.

Because the aluminum panel roof was in good condition, a restoration coating was a practical scope for this project. This was not presented as a replacement of the panel system, and the coating was not applied over an unaddressed active leak. The seams were treated first, then the field coating was applied after the roof was clean and dry.

The Restoration Process

The work followed a straightforward sequence:

  1. The crew cleaned the aluminum-panel roof and cleaned out the surrounding gutters.
  2. They blew the water off the roof and allowed the surface to dry fully.
  3. New tape was installed over the seams where the aluminum panels came together.
  4. Silicone coating was applied over the new seam tape.
  5. One full field coat of white Roof X Tender 985 Super Silicone was applied across the aluminum-panel patio roof.

Peter confirmed that no primer was needed for this project and that one full field coat was applied in accordance with the manufacturer’s specifications, based on his report of the completed work. The post does not infer a coating thickness, coverage rate, warranty, or independent manufacturer certification because those details were not supplied for this project.

Why Seam Preparation Mattered

On an aluminum-panel roof, the panel itself is the visible roof surface, but the joints between panels are important transition points. In this project, those seams were where the reported water entry occurred. Treating the seams before applying the field coat gave the restoration work a defined sequence rather than simply coating over the problem area without preparation.

No polyester fabric was used on this roof. Peter explained that he did not need it for this particular installation because the roof had an approximately 5/12 pitch. That is a project-specific explanation and should not be treated as a universal rule that fabric is unnecessary at every roof slope or with every coating system.

The restoration process also included cleaning the gutters around the patio roof. Keeping the roof surface and drainage areas clean was part of the preparation completed on this project.

For homeowners comparing coating and repair options, BLU Roofing’s residential roof coating guide explains why the roof condition, preparation, product system, and application requirements matter before a coating is selected. Although this project involved a pitched aluminum-panel patio roof rather than a conventional low-slope roof, the repair-first and preparation principles still provide useful context.

Completion and Follow-Up

Peter and one crew member began the project Saturday morning and completed it by early afternoon. The weather was favorable, and there was no weather delay. The quick turnaround reflects this project’s actual scheduling and scope, not a guarantee that every roof coating project can be completed on the same timeline. Roof cleaning, drying, seam work, and coating still have to be completed in the proper order.

At the time this post was prepared, no post-repair rain outcome or customer review had been supplied. The article therefore documents the inspection findings, products, preparation, sequence, and completed work without claiming that the roof has been leak-free for a specific period.

This Delray Beach silicone roof coating project shows how an aluminum-panel patio roof in good overall condition can be restored when the reported water entry is concentrated at the panel seams. The work required careful cleaning and drying, new seam tape, silicone treatment at the seams, and a full field coat across the roof.

BLU Roofing provides roof inspections, repairs, restoration, and replacement for shingle, tile, metal, and flat or low-slope roof systems across Palm Beach, Martin, and Broward Counties. The company works with homeowners on practical roof solutions based on the actual condition of the roof, the reported water-entry area, and the scope required to complete the work properly.

Written By: Peter Menke

Peter Menke is the owner of BLU Roofing and has been serving the South Florida roofing industry for over 6 years. He founded BLU Roofing to provide homeowners with transparent, accurate information grounded in real Florida roofing conditions and building practices. License #CCC1337285.

BLU Roofing provides roof inspections, repairs, restoration, and replacement for shingle, tile, metal, and flat or low-slope roof systems across Palm Beach, Martin, and Broward Counties.

Read More »
West Palm Beach tile roof repair

West Palm Beach Tile Roof Repair: PortoSol Eyebrow Roof Repair

Read More »
emergency roof tarp installation

Emergency Roof Tarp Installation for Insurance Mitigation

This emergency roof tarp installation was completed for insurance mitigation at a single-family home in Miami Lakes, Florida. The active leak was at the connection between a built-up modified flat roof and an exterior wall. BLU Roofing installed a large, heavy-duty 10-mil tarp over the affected area using a non-penetrating method designed to provide temporary protection while the insurance claim and related case were being handled.

Quick Summary

BLU Roofing inspected and temporarily protected an actively leaking roof-to-wall connection on a built-up modified flat roof in Miami Lakes. The work included installing a 36-inch-wide strip of peel-and-stick membrane several inches up the wall and securing it with tape, then covering the affected area with a heavy-duty 10-mil tarp. Rolled furring strips were placed around the tarp perimeter and held down with 50-pound sandbags. No nails, screws, staples, or other fasteners penetrated the roof. The homeowner reported no further leaking for approximately five weeks after installation.

Table of Contents

Project Facts

Project location Miami Lakes, Florida
Property Single-family home
Roof system Built-up modified flat roof connected to a tile roof area
Confirmed problem Active water entry at the connection between the flat roof and exterior wall
Purpose Temporary roof protection for insurance mitigation
Membrane detail Approximately 36-inch-wide peel-and-stick membrane installed several inches up the wall and taped
Tarp Large heavy-duty 10-mil tarp
Perimeter system Rolled furring strips and 50-pound sandbags
Installation method Non-penetrating, with no nails, screws, staples, or other roof fasteners
Timeline Inspection and installation completed during one visit
Reported result No reported leaking for approximately five weeks after installation

Why the Tarp Was Needed

The homeowner had an active leak at the point where the rear flat roof met the exterior wall. If rain occurred before permanent roof work could be completed, water could continue entering through that roof-to-wall connection. The immediate goal was not to perform a permanent roof replacement or represent the tarp as a final repair. The goal was to reduce additional water exposure while the insurance claim and related case were being handled.

The referral came through a public adjusting firm. The insurance claim process was already underway, and adjusters and engineers had been involved. Because the roof condition was part of an ongoing claim and litigation, the temporary protection and supporting documentation were important parts of the mitigation work.

Inspecting the Active Leak

BLU Roofing inspected the roof area before installing the temporary protection. The affected section was a built-up modified roof that was holding water. The water-entry vulnerability was at the transition where the flat roof met the wall. Based on the condition observed, the temporary protection needed to cover the transition and manage water from the wall side of the detail.

The work was completed on a dry visit rather than during active rainfall. The leak itself was active, meaning rain would have allowed water to enter the home, but the installation was scheduled when the roof could be accessed and protected safely.

The completed installation also had to account for the nearby tile roof surface. Thin, lightweight tarps can tear when they are dragged across or weighted on roofing materials, especially around tile profiles. A heavy-duty 10-mil tarp was selected for this temporary application.

Temporary Roof Protection at the Wall

Before the tarp was placed, BLU Roofing installed a 36-inch-wide strip of peel-and-stick membrane at the wall. The membrane extended several inches up the wall and was taped off. This helped cover the immediate roof-to-wall transition before the larger tarp was positioned over the affected area.

The peel-and-stick membrane was part of the temporary mitigation assembly. It was not presented as a permanent reconstruction of the built-up roof system. The tarp remained the primary temporary covering, while the wall membrane helped address the vulnerable transition underneath it.

Non-Penetrating Tarp Installation

The tarp was installed without driving fasteners through the roof. No nails, screws, staples, or similar penetrations were used. Instead, the tarp perimeter was rolled up around furring strips. The furring strips were placed around the full perimeter and held down with 50-pound sandbags.

This arrangement helps keep the tarp perimeter in place without creating additional holes in the roof membrane. The sandbags were positioned over the rolled furring strips so the perimeter remained weighted down if the area experienced wind or heavy rain. The method was selected for temporary protection and was not intended to replace permanent roof repairs.

Because the tarp covered an active roof leak, the installation needed to protect the wall transition while also avoiding unnecessary disturbance to the existing roof. The result was a temporary, non-invasive covering that could remain in place while the insurance-related process continued.

Insurance Mitigation Documentation

BLU Roofing completed the inspection and tarp installation during one visit. The homeowner did not have an out-of-pocket charge for this mitigation work. BLU Roofing billed the insurance carrier and submitted the work documentation to the attorneys handling the case.

The property is located in an HOA, but no permit was required for this temporary tarp installation. The work was performed by one person, and the property was left clean after the installation.

The homeowner later reported that the area had not leaked for approximately five weeks after the tarp was installed. That result is a field report about the temporary covering during that period. It is not a guarantee of future performance and does not change the temporary nature of the installation.

Service Area Note

Miami Lakes is outside BLU Roofing’s normal roofing service area, which primarily includes Palm Beach County, Martin County, and Broward County. This project came through an existing professional relationship with a public adjusting firm, so BLU Roofing was able to assist with this specific insurance-mitigation need.

For homeowners outside the normal service area, the best first step is to contact BLU Roofing and describe the situation. If the project is not practical for BLU Roofing to handle directly, Peter can refer the homeowner to qualified roofing professionals in the appropriate area when possible. BLU Roofing’s roof repair service page provides additional information about the inspection and repair work typically handled within the regular service area.

This emergency roof tarp installation was a temporary protection measure for a documented active leak. A tarp can help reduce additional water exposure while a claim or permanent repair is being addressed, but it should not be confused with a completed roof repair or replacement.

Written By: Peter Menke

Peter Menke is the owner of BLU Roofing and has been serving the South Florida roofing industry for over 6 years. He founded BLU Roofing to provide homeowners with transparent, accurate information grounded in real Florida roofing conditions and building practices. License #CCC1337285.

BLU Roofing provides roof inspections, repairs, restoration, and replacement for shingle, tile, metal, and flat or low-slope roof systems across Palm Beach, Martin, and Broward Counties.

Read More »
Riviera Beach tile roof repair

Riviera Beach Tile Roof Repair: Multiple Leaks at a Turtle Cay Townhouse

This Riviera Beach tile roof repair addressed multiple leak areas on a concrete tile townhouse roof in Turtle Cay, Riviera Beach, Florida. The rental property had water entering through the garage ceiling, with a ceiling stain and mold visible on the wall. The initial inspection found a leak at a roof return and bottom valley, and additional inspection identified leaking gooseneck vents. When the roof was opened, another leak was found to the side, bringing the project to approximately four separate leak areas.

Quick Summary

BLU Roofing repaired approximately four leak areas on a concrete tile townhouse roof in Turtle Cay, Riviera Beach. The leak entered through the garage ceiling and included a roof return and bottom valley, two gooseneck vents, and an additional side area discovered after the roof was opened. The crew replaced rotted decking at the return, rebuilt the affected roofing system with CertainTeed SA granulated cap sheet, resealed the valley and roof-to-wall flashing with Polyglass PG 500 and APOC 470 reinforcing fabric, reflashed the gooseneck vents, reused the existing tiles, repaired broken tiles, and reset the tiles with ICP Polyset AH-160 adhesive foam.

Table of Contents

Project Facts

Community Turtle Cay, Riviera Beach, Florida 33407
Property Townhouse and rental property
Roof system Older concrete tile roof, still considered repairable
Interior symptom Garage ceiling leak, ceiling staining, and mold on the wall
Confirmed areas Roof return and bottom valley, two gooseneck vents, and an additional side leak
Decking Rotted plywood at the return area was replaced; no other rotted decking was found
Waterproofing materials CertainTeed SA granulated cap sheet, Polyglass PG 500, and four-inch APOC 470 reinforcing fabric
Tile installation Existing tiles reused where possible, broken tiles repaired, and tiles reset with ICP Polyset AH-160 adhesive foam
Timeline Two days with a two- to three-person crew because additional leaks were found after opening the roof
Follow-up Completed approximately one month before publication, with substantial rain and no callbacks reported

The Initial Leak and Attic Inspection

The rental property’s tenant or occupants were dealing with water entering through the garage ceiling. By the time BLU Roofing was called, there was a ceiling stain and mold visible on the wall. The property had attic access, which allowed the leak to be traced from inside rather than relying only on the visible roof surface.

The initial leak was located at the roof return and bottom valley area. This was a useful example of why returns, valleys, and roof-to-wall transitions deserve careful attention. They are areas where water can concentrate or change direction, and they often include several connected details that must work together.

BLU Roofing’s roof repair service includes investigating localized leaks, damaged decking, flashing details, and water entry around roof penetrations. The correct repair depends on what is found during the inspection rather than assuming that the first visible symptom identifies the complete problem.

Multiple Leak Areas Found During the Repair

The attic inspection identified the return and bottom valley leak, along with leaks at two gooseneck vents. The roof was opened so the affected areas could be inspected down to the decking. Once the tiles and underlayment were removed, another leak was found off to the side.

That brought the project to approximately four separate leak areas:

  • The roof return and bottom valley area
  • One leaking gooseneck vent
  • A second leaking gooseneck vent
  • An additional side leak discovered after opening the roof

Rotted plywood was found at the return area and replaced. Outside that return location, no other rotted decking was found. The other leaks were newer and had not caused the same level of deterioration. This is one reason opening a localized repair area can reveal information that is not visible from the roof surface or from the interior of the building.

Rebuilding the Return and Valley

The crew removed the concrete tiles and cut out the existing underlayment down to the roof decking. The damaged decking at the return was removed and replaced. The affected roofing system was then rebuilt using CertainTeed SA granulated cap sheet, tied into the existing roof system with Polyglass PG 500 modified cement and four-inch APOC 470 asphalt-saturated reinforcing fabric.

The return and bottom valley were resealed with the same waterproofing materials. The valley above the return was also addressed, along with the roof-to-wall flashing above the valley. This allowed the repair to address the connected water-shedding details instead of treating only the point where the leak became visible inside the garage.

Polyglass identifies PG 500 as a trowel-grade modified cement used for flashing details, membrane attachment, and waterproofing repairs. APOC 470 is an asphalt-saturated cotton reinforcing fabric used to reinforce roof repair areas. Product selection and installation remain dependent on the specific roof assembly and field conditions.

Reflashing the Vents and Roof-to-Wall Detail

The two leaking gooseneck vents were reflashed and tied into the roof system with roofing cement and reinforcing membrane. The roof-to-wall flashing was also resealed using the same PG 500 and APOC 470 membrane approach.

The vent repairs were included because the attic inspection identified water entering at those locations. They were not treated as a generic add-on. Each area was addressed based on what was observed during the inspection and after the surrounding roof materials were opened.

This type of repair can involve several connected details. A valley can direct water toward a return, a wall transition can receive concentrated runoff, and a vent can leak independently within the same roof section. A durable repair requires separating those conditions and rebuilding each affected area correctly.

Completing the Repair

After the underlayment and flashing work was completed, the existing concrete tiles were reinstalled wherever they could be reused. Broken tiles found during the work were repaired. The tiles were reset with ICP Polyset AH-160 two-part polyurethane adhesive foam rather than relying on unnecessary penetrations through the tile surface.

The project took two days with a two- to three-person crew. The additional time was needed because more leaks were discovered after the roof was opened. The repair was completed at the originally agreed price, even though the opened roof revealed more work than was visible during the initial inspection.

Weather was monitored throughout the project, as it is with South Florida roofing work, especially during the August and September rainy season. The crew completed the work with the necessary weather conditions in mind and meticulously cleaned the property when finished. A complete before, during, and after photo report was created in CompanyCam.

One Price Despite Additional Findings

Roof repairs sometimes change once the affected area is opened. In this Turtle Cay project, the attic inspection found the main return leak and the vent leaks, but the roof opening revealed an additional side leak and rotted decking at the return. BLU Roofing handled the added repair work without increasing the original price.

The repairs were completed approximately one month before this Project Spotlight was prepared. The roof has received substantial rain since then, and there have been no callbacks. That follow-up does not replace a long-term roof inspection, but it is a useful field outcome for this documented repair project.

This Riviera Beach tile roof repair shows why a leak should be traced through the attic and roof assembly instead of treating only the first visible stain. Returns, bottom valleys, roof-to-wall flashing, gooseneck vents, underlayment, and decking can all be part of the same water-entry investigation.

Written By: Peter Menke

Peter Menke is the owner of BLU Roofing and has been serving the South Florida roofing industry for over 6 years. He founded BLU Roofing to provide homeowners with transparent, accurate information grounded in real Florida roofing conditions and building practices. License #CCC1337285.

BLU Roofing provides roof inspections, repairs, restoration, and replacement for shingle, tile, metal, and flat or low-slope roof systems across Palm Beach, Martin, and Broward Counties.

Read More »
Heritage Farms shingle roof repair

Heritage Farms Shingle Roof Repair: Finding a Leak in a Spray-Foam Attic

This Heritage Farms shingle roof repair involved a difficult-to-locate leak on an eight-year-old asphalt shingle roof in the Heritage Farms equestrian community near Lake Worth and Wellington, Florida. Because the home has a spray-foam-insulated attic, water was moving through and being held by the foam before dripping into the attic. The first suspected source was the nearby kitchen hood gooseneck vent, but controlled hose testing showed that the leak was actually farther up the roof.

Quick Summary

BLU Roofing diagnosed and repaired a field leak on an eight-year-old shingle roof in Heritage Farms. The crew tested the gooseneck vent first, then worked upward row by row until the leak was isolated approximately five feet above and to the left of the vent. The repair included removing shingles and old 30-pound felt, installing Polyglass Polystick TU Plus, tying it into the existing system with Polyglass PG 500 and APOC 470 reinforcing fabric, reinstalling GAF HDZ Shakewood shingles, resealing the gooseneck vent, and completing a final 15 to 20-plus-minute hose test.

Table of Contents

Project Facts

Community Heritage Farms, an equestrian community near Lake Worth and Wellington, Florida 33449
Property Single-family home
Roof system Eight-year-old asphalt shingle roof from new construction
Reason for service Dripping noise and water entering the attic during heavy rain
Initial suspected source Kitchen hood gooseneck vent
Confirmed leak area Approximately five feet above and to the left of the gooseneck vent, in the shingle field
Underlayment repair Polyglass Polystick TU Plus tied into the existing system with Polyglass PG 500 and APOC 470 reinforcing fabric
Shingles GAF HDZ shingles in a Shakewood color selected to match the existing roof as closely as possible
Testing Initial and final controlled hose tests, with the final test lasting approximately 15 to 20 minutes or longer
Timeline Half-day repair completed in the morning by Peter and his foreman

Why This Leak Was Hard to Find

The homeowner first noticed a dripping noise in the attic and initially suspected the kitchen hood gooseneck vent. That was a reasonable assumption because the vent was visible near the area where the sound appeared to be coming from. A first hose test around the vent did not produce water inside the attic.

The situation became more complicated when the roof was inspected from inside. This home has a spray-foam-insulated attic, so the foam covers the underside of the roof deck and prevents the normal visual inspection that is possible in an unfinished or conventionally insulated attic. The foam was also holding water and allowing it to travel before releasing it as a drip. That meant the point where water appeared inside was not necessarily the point where water entered the roof.

There was also buckling in portions of the plywood roof deck where expanding spray foam appears to have pushed through seams between decking panels. The buckling was observed in multiple areas of the roof and was not corrected as part of this localized leak repair. It was documented as an existing roof condition, not identified as a confirmed cause of this particular leak.

Controlled Hose Testing Isolating the Leak

Because the roof could not be fully evaluated from below, the diagnosis required a controlled hose test with one person on the roof and one person in the attic. The test began at the gooseneck vent. The crew worked upward row by row, applying water to a controlled area and then checking the attic for a response.

That process isolated the leak approximately five feet above and to the left of the gooseneck vent. The water was entering through the shingle field rather than the vent itself. There was an exposed nail in the area, sometimes called a shiner in roofing, along with wet plywood below the repair area. The plywood was damp, but it was not rotted or deteriorated because the leak was caught quickly.

The homeowner had previously experienced another leak on this relatively young roof. This project illustrates why a roof leak should be diagnosed instead of automatically repairing the nearest penetration. The closest vent may be dry while water is entering higher on the roof and traveling through the assembly before appearing inside.

Repairing the Shingle Roof

The repair area was opened from the shingle surface down to the roof deck. The shingles were removed, along with the existing 30-pound roofing felt. The exposed deck was inspected, and the damp plywood was found to be serviceable. No plywood replacement was necessary.

New Polyglass Polystick TU Plus self-adhered underlayment was installed over the repair area. The new material was tied into the existing underlayment system with Polyglass PG 500 modified cement and four-inch APOC 470 asphalt-saturated reinforcing fabric. PG 500 is a trowel-grade bonding and waterproofing material that Polyglass identifies for flashing details and membrane repairs. APOC 470 is an asphalt-saturated cotton reinforcing fabric used to reinforce roof repair areas.

The repair area was extended down to the top of the gooseneck vent so the surrounding transition could be addressed as part of the work. The top of the gooseneck vent flashing was also resealed and tied into the membrane repair with PG 500 and reinforcing fabric. This did not mean the vent was the confirmed source of the leak. It was included because the repair area reached the vent and the surrounding detail needed to be properly closed back up.

After the underlayment work was completed, the crew reinstalled the shingles using GAF HDZ shingles in a Shakewood color selected to match the existing roof as closely as possible. The repair was tied into the surrounding shingle field so the roof could be closed and tested before the crew left.

Final Testing and Documentation

After the initial repair, the crew performed another hose test. Water had stopped in three of the four areas that had been dripping, but one area continued to release a small amount of water. Because the spray foam attic was holding water, a small section of foam had to be removed to release the trapped water and expose the remaining active area.

The crew then tested directly above that location, found the last remaining leak point, repaired it, and performed another hose test. The final test lasted approximately 15 to 20 minutes or longer, long enough to allow water to reach the repaired area and confirm the result. No further water entry was observed after the final repair.

Testing roof repairs before leaving is good practice when the roof area can be safely tested. It gives the contractor an opportunity to find a remaining leak before the job is closed out and can help reduce the chance of an unnecessary callback. In this case, the additional test found a small amount of water that had remained trapped in the spray foam, allowing the crew to correct the final issue the same morning.

Peter and his foreman completed the repair in approximately half a day. The work was finished before the afternoon showers arrived. Before, during, and after photos were recorded in a CompanyCam report, and the work area was cleaned carefully before the crew left. No HOA approval or permit was required for this localized repair.

Customer Feedback

The homeowner supplied the following review after the repair:

Heritage Farms Shingle Roof Repair Customer Review
Homeowner feedback after BLU Roofing diagnosed and repaired a difficult-to-locate shingle roof leak in Heritage Farms near Lake Worth and Wellington.

A difficult-to-trace leak does not always come from the closest roof penetration. Spray foam, roof pitch, decking conditions, and water migration can all affect where a leak appears inside a home. A controlled inspection and testing process can help identify the actual entry point before a repair is recommended.

Written By: Peter Menke

Peter Menke is the owner of BLU Roofing and has been serving the South Florida roofing industry for over 6 years. He founded BLU Roofing to provide homeowners with transparent, accurate information grounded in real Florida roofing conditions and building practices. License #CCC1337285.

BLU Roofing provides roof inspections, repairs, restoration, and replacement for shingle, tile, metal, and flat or low-slope roof systems across Palm Beach, Martin, and Broward Counties.

Read More »